Constructional Difficulty: Hard. Surface mount soldering. Oscilloscope needed for calibration.
The Oakley Flanger & Chorus module is an analogue delay line capable of delaying audio signals from 0.5mS to 15mS. In conjunction with an external LFO module this unit can be used to produce real time vibrato, chorus and flanging effects. With the feedback control set to maximum the module can be set to self-oscillate
The delayed audio output is available from the DLY OUT socket. While the MIX OUT socket has a equal mix of input signal and delayed signal. The phase of the delayed signal that is mixed may be selected to be inverted (NEG) or non-inverted (POS) by the use of the MIX switch. This is particularly useful when used for chorus or flanging as the two modes can create completely different effects.
A feedback path from the delayed output back to the input is available and you have control over both the amount, via the FEEDBACK pot, and phase of the signal, via the FBK switch. Inserting a jack plug into the FBK IN socket will break the internal feedback path and allow another signal to be sent into the delay line. This could allow additional processing of the raw delayed signal, from the DLY OUT socket, prior to being sent back into the delay line again. For example, using a VCA to process the feedback signal would allow CV control of the feedback level.
There are two control voltage (CV) inputs. CV1 has a fixed sensitivity while CV2 has its own sensitivity control. CV2's control pot is a reversible attenuator, so you are able to adjust not only the depth of the modulation but also the polarity. Although not specifically designed to track to 1V/octave, using the CV1 input, the module can be used as tuned delay line over a useful proportion of the full operating range.
The delay line itself is based around two 3207 bucket brigade delay (BBD) devices controlled by a voltage controlled oscillator (VCO) running from around 33kHz to over 1MHz. Audio bandwidth of the delayed signal extends to 14kHz and several unusual design features ensure that the module is relatively quiet compared to other units of its type.
Two LEDs provide visual indication of the signal level being sent to the BBD devices. The DRIVE control should be adjusted to ensure that the green LED remains lit for optimum signal level. The red LED will light when the signal level is close to, or is, being overdriven. The module will not be harmed when the signal is overdriven and there is a soft clipping circuit in place to ensure the overdriven sound is musically useful. The DRIVE control allows a variety of different signal levels to be used with the module although the expected signal level would be expected to be between 0.5V(peak) and 8V(peak).
The printed circuit board (PCB) uses a mixture of through hole and surface mount components. The op-amps, non-polar capacitors, resistors and small diodes are all surface mount. The op-amps are SO8 packages, capacitors and resistors 0805 and diodes SOD323. Most builders should find these no problem to solder even if they have not assembled modules with surface mount devices before. To calibrate the unit an oscilloscope is useful but not essential.
The module accommodates either our standard Oakley/MOTM power header or a Synthesizers.com power header. The supply voltage is +/-15V and current consumption is around +75mA and -45mA.
The PCB is 109mm (deep) x 124mm (height). The PCB is a four layer design, has tough solder mask both sides, and has bold component legending for ease of construction.
The Oakley Flanger as a single width MOTM format module in a natural finish Schaeffer panel. Note also the use of our optional Sock6 socket board to help keep the wiring to the sockets neat and tidy.
Quick track recorded using an Oakley modular to showcase the Oakley Flanger/Chorus module. Lead line is one VCO passed through a DLF filter, Discrete VCA and onto the Flanger/Chorus. Bass in the second half is the same patch but this time the filter is being swept with a VRG and the flanger module is used to create a deep chorus sound. Some reverb used on the leadline and plucked bell sound.
Nord Lead A1 string machine patch being processed through the Oakley Flanger/Chorus. Slow triangle wave LFO and with the Flanger/Chorus module set to relatively high positive feedback. Some light reverb has been added.
Nord Lead A1 string machine patch being processed through the Oakley Flanger/Chorus. Slow triangle wave LFO and with the Flanger/Chorus module set to relatively high negative feedback. Some light reverb has been added.
Simple traditional VCO-VCF-VCA patch. First part is completely dry, and then other parts sent into the Flanger/Chorus module. Settings changed manually as the same simple sequence goes round and round. Second and third show the chorus sound. Fourth bit decreases the delay time to give the classic flanging - increasing the feedback creates a deep flanger sound. Fifth bit is another flanger but uses negative feedback. Sixth part is manually altering the controls for excessive effects, firstly with positive feedback and then negative feedback.
Standard VCO-VCF-VCA patch using the flanger module to shift the pitch. Firstly you hear the pitch being bent by an EG triggered from the gate on a simple riff, then a filtered constant pitch sawtooth being pitch shifted by a LFO - firstly subtle and then more extreme. The final samples in this collection are filtered white noise being flanged. The delay time and feedback controls are being manually altered. The first part you hear is positive feedback and the second is negative feedback.
The PCB is populated with both surface mount devices (0805 resistors and capacitors, SOD323 diodes & small outline ICs) and standard through hole components.
Click here for ordering details.
Flanger issue 2 PCB ...................................................... 25GBP
Sock6 issue 2 PCB
Flanger pot bracket kit ................................................ 0.75GBP
The optional Pot Bracket Kit contains the three 16mm Alpha pot brackets required to complete one module.
All other parts can be purchased from your usual electronic component supplier.
All prices include VAT at UK rates. Shipping is additional to these prices. See also the FAQ page.
Flanger/Chorus Builder's Guide
Flanger/Chorus User Manual
Construction Guide Our handy guide to building Oakley DIY projects
Parts Guide Our handy guide to buying parts for Oakley DIY projects.
Schematics are only available to purchasers of the PCB and will be sent via e-mail when the board(s) are shipped.
Front Panel database
A Schaeffer front panel can be made for this module. The databases can be found by downloading the following links:
5U format 1U wide module in traditional black
5U format 1U wide module in natural (silver) finish
To read these files you will need a copy of 'Frontplatten designer' from Schaeffer. The program also features on-line ordering, so its now even easier to buy your panels from Scheaffer.
The company are based in Berlin in Germany and will send out panels to anywhere in the world. Delivery to the UK normally takes around ten days. For North American users you can also order your Schaeffer panels from Front Panel Express.
Back to projects page: Projects
Back Home: Oakley Sound